1. Noțiuni de bază despre echipament

1.1 de parametri măsurabili

Nota: LS2090-IEC, based on the LS2090 and equipped with custom software (available at an additional cost), fully complies with the relevant requirements of EN/IEC 61000-3-2:2019.

1.2 Verificarea configurației echipamentului

1.2.1 Despachetarea

Când despachetați dispozitivul, manipulați-l cu grijă pentru a evita zgârierea carcasei cu unelte ascuțite. După despachetare, inspectați mai întâi exteriorul dispozitivului pentru a vă asigura că nu există deformări sau lovituri vizibile și că butoanele nu sunt deteriorate sau slăbite. Dacă observați anomalii la dispozitiv sau la accesoriile sale, nu îl porniți. Vă rugăm să ne contactați imediat.

1.2.2 Unitatea principală și accesoriile

The host is as follows.

Principalele componente ale LS2090 device are as follows (Figure 1-1):

Figura 1-1

1.2.3 Descărcarea documentelor electronice

We have already sent download links for the electronic user manual, software, calibration certificate, warranty card, and other items via email at the time of shipment. Please download them promptly. If you have not received the email, please contact us to request the download links again.

2. Măsuri de siguranță

2.1 Siguranța electrică

Before connecting the power cord, verify that the supply voltage is AC 220V ±10% and the frequency is 50 Hz or 60 Hz. You must use a three-prong outlet with a protective ground, and the protective ground resistance must be ≤4 Ω. Never cut or disconnect the protective ground wire, as doing so poses a risk of electric shock.

2.2 Siguranța mediului

Do not use in environments with flammable or explosive materials, strong electromagnetic interference, high temperatures and humidity, or excessive dust levels. Operating environment: Temperature 5°C to 35°C, relative humidity ≤ 65% RH.

2.3 Proceduri de operare

Before connecting the wires, the power supply to the sample load must be disconnected; do not connect wires while the circuit is energized. Connect voltage leads in parallel and current leads in series; under no circumstances should a current circuit be connected to a voltage terminal or a voltage circuit to a current terminal. Pay attention to the positive and negative polarities when performing DC measurements. After connecting the wires, tighten the terminals and ensure that no bare wires are exposed to prevent short circuits or electric shock.

When measuring high-frequency signals, keep the wiring as short as possible and use thick, multi-strand wire; route the wiring away from the metal casing of the equipment to minimize interference from distributed capacitance.

3. Funcționarea echipamentelor

3.1 Introducere în panoul frontal

See Figure 3-1. Note: Using the desktop software makes operation more convenient and eliminates the need to use the front panel of the device; if you need to print a test report, you must also do so through the software. If you use the software, you only need to operate the power switch and load switch on the front panel.

Figura 3-1

3.2 Introduction to the Back Panel and Wiring

Note: To ensure safety during operation, make sure the load power switch on the front panel of the equipment is in the off (up) position before connecting the wires.

3.2.1 Using LED Light Sources

Figura 3-2

3.2.2 Using the MB98 DC Electronic Load

See Figure 3-3. Connect the LED LOAD to the MB98 series electronic load, observing the correct polarity. All other connections are the same as in Section 3.2.1.

Figura 3-3

3.3 Equipment Testing Procedures

3.3.1 Using LED Light Sources

3.3.2 Using the MB98 DC Electronic Load

4. Software Operation (Using the LS2090-IEC Software as an Example)

4.1 Instalarea software-ului

Software System Requirements: Computers running Windows 7 or later.

LS2090 connects to the computer via an RS-232 cable. If the computer does not have an RS-232 port, you will need to use an RS-232-to-USB adapter cable to connect the two devices.

See Figure 4-1 for the software installation package.

Figura 4-1

4.2 Prezentare generală a software-ului

4.2.1 Software Start Screen

Vezi Figura 4-2.

Figura 4-2

4.2.2 System Configuration Interface

Vezi Figura 4-3.

Figura 4-3

4.2.3 Product Information Screen

Vezi Figura 4-4.

Figura 4-4

4.3 Software Testing Procedures

5. Întreținerea și îngrijirea zilnică a echipamentelor

5.1 Întreținerea de rutină

5.1.1 Curățare zilnică

Be sure to turn off the power and unplug the power cord before cleaning. We recommend wiping the unit with a soft, antistatic cotton cloth and a mild detergent; do not spray liquids directly onto the unit. Do not use chemical solvents such as benzene, toluene, or acetone.

5.1.2 Inspecții de rutină

Before each use, check the power cord and terminal connections to ensure there are no loose connections or signs of burn damage; after turning on the unit, verify that the indicator lights and display are functioning properly.

5.2 Specificații de stocare

5.2.1 Cerințe privind mediul de stocare

Temperatură: 5°C până la 35°C; umiditate relativă: ≤65% RH; mediu uscat, fără praf și fără gaze corozive.

5.2.2 Operațiuni de depozitare pe termen lung

Turn off the power and unplug all cables; clean the equipment and wrap it in dust-proof film; power it on for 30 minutes each month to prevent moisture damage to the components.

5.3 Cerințe privind intervalul de calibrare

Pentru a asigura acuratețea măsurătorilor și fiabilitatea operațională a echipamentului, se recomandă trimiterea periodică a acestuia la un laborator de metrologie terț calificat pentru calibrare. Intervalul de calibrare recomandat este de 12 luni. Utilizatorii pot determina intervalul specific de calibrare în funcție de frecvența de utilizare, condițiile de mediu și cerințele sistemului de calitate.

6. Depanarea și rezolvarea problemelor comune

7. Lista de impachetat